pi01s/d s ries 1w dc/dc converter, high isol ation, sip - package ds_ pi01s/d _ 0 3 20 2012 e - mail : dcdc @ d elta.com.tw http://www.delta.com.tw/dcdc p1 features ? efficie ncy up to 75 % ? sip package with industry standard pinout ? high isolation volage 6000 vdc ? l ead free ,rohs complian ? industrial & medical safety approval ? operating temperature range - 25c to +85c ? low isolation capacitance ? >2 mhours mtbf ? 3 years product warran ty the pi01s/d series are miniature, sip package, isolated 1w dc/dc converters with 6,000vdc isolation. it allows a wide operating temperature range of C 25c to +85c. with high isolation, pi01s/d is suitable for all kinds of medical device application. t hese high isolated dc/dc converters are the latest offering from a world leader in power systems technology and manufacturing D delta electronics, inc. model list model number input voltage (range) output voltage output current input current load regulation max. capacitive load efficiency (typ.) max. min. @max. load @no load @max. load vdc vdc ma ma ma(typ.) ma(typ.) % (max.) uf % pi01s0505a 5 (4.5 ~ 5.5) 5 200 4 303 55 10 680 66 pi01s0512a 12 80 2 291 8 66 pi01s0515a 15 65 1 295 8 66 pi01d 0505a 5 100 2 303 10 220* 66 pi01d0512a 12 40 1 267 8 72 pi01d0515a 15 35 1 287 8 73 pi01s1205a 12 (10.8 ~ 13.2) 5 200 4 126 30 10 680 66 pi01s1212a 12 80 2 121 8 66 pi01s1215a 15 65 1 123 8 66 pi01d1205a 5 100 2 126 10 22 0* 66 pi01d1212a 12 40 1 108 8 74 pi01d1215a 15 35 1 117 8 75 * for each output
ds_ pi01s/d _ 0 3 20 2012 e - mail : dcdc @ d elta.com.tw http://www.delta.com.tw/dcdc input characteristics parameter model min. typ. max. unit input voltage range 5v input models 4.5 5 5.5 vdc 12v input models 10.8 12 13.2 input surge vol tage (1 sec. max.) 5v input models - 0.7 --- 9 12v input models - 0.7 --- 29 reverse polarity input current all models --- --- 0.3 a input filter lc filter internal power dissipation --- --- 650 mw output characteristics parameter conditions min. typ. max. unit output voltage accuracy --- 1.0 3.0 % output voltage balance dual output, balanced loads --- 0.1 1.0 % line regulation for vin change of 1% --- 1.2 1.5 % load regulation io=20% to 100% see model selection guide ripple & noise (2 0mhz) --- 100 150 mv p - p ripple & noise (20mhz) over line, load & temp. --- --- 200 mv p - p ripple & noise (20mhz) --- --- 15 mv rms temperature coefficient --- 0.01 0.02 %/ short circuit protection 0.5 second max. isolation and safety standards parameter conditions min. typ. max. unit i/o isolation voltage (rated) 60 seconds 3000 --- --- vacrms i/o isolation test voltage flash tested for 1 second 4500 --- --- v pk i/ o isolation resistance 500 vdc 10 --- --- g i/o isolation capacitance 100khz, 1v --- 15 20 pf safety standards cul/ul60950 - 1, csa c22.2 no. 60950 - 1 - 03 ul60601 - 1,csa c22.2 no.601 - 1 iec/en 60950 - 1, iec/en 60601 - 1 approvals iec60950 - 1 cb report, cul/u l 60950 - 1 certificate ul60601 - 1 ul certificate general characteristics parameter conditions min. typ. max. unit switching frequency 50 80 100 khz mtbf (calculated) mil - hdbk - 217f@25 , ground benign 2,000,000 --- --- hours recommended input fuse 5 v input models 12v input models 500ma slow - blow type 200ma slow - blow type environmental specifications parameter conditions min. max. unit operating temperature range (with derating) ambient - 25 +85 case temperature --- +90 storage temperature range - 50 +125 humidity (non condensing) --- 95 % rel. h cooling free - air convection lead temperature (1.5mm from case for 10sec.) --- 260 p 2
ds_ pi01s/d _ 0 3 20 2012 e - mail : dcdc @ d elta.com.tw http://www.delta.com.tw/dcdc power derating curve notes 1 specifications typical at ta=+25 , resis tive load, nominal input voltage and rated output current unless otherwise noted. 2 ripple & noise measurement bandwidth is 0 - 20mhz. 3 these power converters require a minimum output loading to maintain specified regulation, o peration under no - load condi tions will not damage these modules; however they may not meet all specifications listed. 4 all dc/dc converters should be externally fused at the front end for protection. 5 specifications subject to change without notice. p 3 ~ a m b i e n t t e m p e r a t u r e o u t p u t p o w e r ( % ) 0 2 0 4 0 6 0 8 0 1 0 0 - 2 5 0 2 0 6 0 1 0 0 1 1 0 8 0 4 0 4 0 0 l f m 2 0 0 l f m 1 0 0 l f m n a t u r a l c o n v e c t i o n
ds_ pi01s/d _ 0 3 20 2012 e - mail : dcdc @ d elta.com.tw http://www.delta.com.tw/dcdc mechanical drawing mechanical dimensions pin connections pin single output dual output 1 +vin +vin 2 - vin - vin 5 - vout - vout 6 no pin common 7 +vout +vout ? all dimensions in mm (inches) ? tolerance: x.x 0.25 (x.xx0.01) x.xx 0.13 ( x.xxx0.00 5) ? pins 0.05 (0.002) physical outline case size : 22.0x7.5x12.5mm (0.87x0.30x0.49 inches) case material : non - conductive black plastic (flammability to ul 94v - 0 rated) weight : 3.9g p 4 0.5 [0.02] 3.50 [0.14] 2.54 [0.10] 7.62 [0.30] 2x2.54 [2x0.10] 22.0 [0.87] 21.0 [0.83] 0.50 [0.02] bottom view 0 . 2 5 [ 0 . 0 1 ] 7 . 5 [ 0 . 3 0 ] 0 . 5 [ 0 . 0 2 ] 1 2 . 5 [ 0 . 4 9 ] 3 . 2 [ 0 . 1 3 ] 1 2 5 6 7 2 . 0 [ 0 . 0 8 ]
ds_ pi01s/d _ 0 3 20 2012 e - mail : dcdc @ d elta.com.tw http://www.delta.com.tw/dcdc part numbering system p i 01 s 05 12 a form factor family series watt number of outputs input voltage output voltage option code d - dip a~z 01:1w s - single 03:3.3v 03:3.3v a - std. functions p - sip 02:2w d - dual 05: 5v 05: 5v s - smd 03:3w 12:12v 12:12v 04:4w 24: 24v 15: 15v 06:6w 48:48v 24: 24v warranty delta offers a t hree ( 3 ) year s limited warranty. complete warranty information is listed on our web site or is available upon request from delta. information furnished by delta is belie ved to be accurate and reliable. however, no responsibility is assumed by delta for its use, nor for any infringements of patents or other rights of third parties, which may result from its use. no license is granted by implicatio n or otherwise under any p atent or patent rights of delta. delta reserves the right to revise these specifications at any time, without notice. p 5
|
